# Pool Plant Room Relocation & Re-Plumbing Melbourne | Palatial Pools

URL: https://palatialpools.com.au/pool-plant-room-relocation-melbourne/

Moving pool equipment or rebuilding a plant room in Melbourne: new runs sized for the distance, old buried lines tested before reuse, clean handover. Call 03 4517 6657.

[Home](https://palatialpools.com.au/)/[Custom pool plumbing](https://palatialpools.com.au/pool-plumbing-melbourne/)/Plant-room relocation and full re-plumbingMove it once, plumb it properly

# Plant Room Relocation & Full Re-Plumbing

Renovations, noise complaints, a new garage or a cramped side passage are all good reasons to move pool equipment. Done well, it's a chance to fix decades of patchwork. Done badly, it adds distance and friction that the old pump was never sized for.

Request a quote[03 4517 6657](tel:+61345176657)

Distance planned for

Longer runs mean more friction. We size pipe and pumps for the new layout.

Old lines proven first

Buried pipework pressure tested before anyone decides to keep it.

Trades coordinated

Gas and electrical work sequenced with licensed trades where required.

New runs sized for the new distance, with buried pipework tested before it's reused.

## What changes when the plant moves

01

### Every extra metre costs head

Moving the plant further from the pool adds pipe length, fittings and often height. Unless the pipe size goes up to suit, flow drops and the pump works harder. We re-run the hydraulics for the new position.

02

### Suction is the sensitive side

Long suction runs are where air leaks, prime loss and cavitation show up first. We keep suction runs as short and straight as the site allows and size them generously.

03

### Old buried lines get tested

Reusing buried pipework saves digging, but only if it holds. Each line is isolated and pressure or vacuum tested before it's connected to new equipment.

04

### The new space has to work

Ventilation for heaters and heat pumps, drainage for wash-down and filter backwash, flue clearances and service room all decide where the equipment can sensibly go.

## Good reasons to move

Common triggers are a renovation or extension taking over the old pad, equipment too close to a neighbour's bedroom, flooding or poor drainage at the old spot, or simply no room to service anything. EPA Victoria's prohibited hours for pool pumps and heat pumps, which apply when they can be heard inside a neighbour's habitable room overnight, are often what starts the conversation.

## Sequenced with the build

On renovation projects we plan the new runs early, so sleeves and penetrations go in before slabs and paving. Where gas or electrical work is involved, that's done by appropriately licensed trades and sequenced with the plumbing so the pool is out of action for as short a time as possible.

## Process

On complex builds, the space is captured with LiDAR at 40 million points per square metre to 0.5 mm accuracy, reconstructed in COLMAP and TwinVision, and every pipe run and hydraulic calculation is modelled in OpenFOAM on Palatial's own frontier hardware, before a single fitting is cut.

An older pool equipment pad with a sand filter and pump against a brick wall.

What we measure and specify

- New run lengths, heights and fittings
- Pipe sizing for the new distance
- Pressure and vacuum test of lines being kept
- Ventilation, drainage and flue clearances
- Noise exposure to neighbouring habitable rooms
- Sleeves and penetrations before slabs and paving

What you get

### A plant in the right place

Quieter, drier and easier to service than where it was.

### Hydraulics re-run

Pipe and pump sized for the new layout, not inherited from the old one.

### A tested system

Joints pressure tested and every mode run before handover.

Questions

## Plant Room Relocation & Full Re-Plumbing: common questions

Will moving the pump make my pool flow worse?+

It can if the extra distance isn't planned for. We size the new pipework for the new layout, so flow at the returns holds up.

Can you reuse the existing underground pipes?+

If they pass a pressure or vacuum test, often yes. If they don't, we'd rather know before the new equipment goes in.

Who handles gas and electrical work?+

Licensed trades do any gas or electrical work required, coordinated with our plumbing.

How long is the pool out of action?+

It depends on the scope. We plan the sequence so the changeover itself is as short as possible, and tell you up front.

Related specialist plumbing

[Hydraulic design, flow and head-loss planningFlow, head and balance worked out before a single fitting is cut.](https://palatialpools.com.au/pool-hydraulic-design-melbourne/)[Leak and pressure diagnosticsEach line isolated and tested on its own, so any digging starts in the right place.](https://palatialpools.com.au/pool-plumbing-pressure-testing-melbourne/)[Custom manifolds and plant roomsCustom manifolds that let every line be set, isolated and serviced on its own.](https://palatialpools.com.au/custom-pool-manifold-plant-room-design-melbourne/)[All custom pool plumbingRepairs through to full plant room builds.](https://palatialpools.com.au/pool-plumbing-melbourne/)

Try the [pump optimiser](https://palatialpools.com.au/pump-optimiser/) or the [filter sizing calculator](https://palatialpools.com.au/filter-sizing/) for a first look, or book a [pool inspection](https://palatialpools.com.au/inspections/).

Enquiries and quotes

## Talk to us about your plumbing

Send a few wide photos of the plant and a short description of what the pool needs to do. We'll come back with the right first step.

[03 4517 6657](tel:+61345176657)[0420 117 665](tel:+61420117665)[service@palatialpools.com.au](mailto:service@palatialpools.com.au)

Monday-Friday 9:30am-4:30pm, Saturday 9:30am-3:30pm. Sunday closed.

NamePhoneEmailSuburb (optional)How can we help?WebsiteA phone number or an email address is enough.

Send enquiry
