# Custom Pool Manifold & Plant Room Design Melbourne | Palatial Pools

URL: https://palatialpools.com.au/custom-pool-manifold-plant-room-design-melbourne/

Custom pool manifolds and plant rooms designed and built in Melbourne. Every line on its own valve, every valve labelled, every path serviceable. Call 03 4517 6657.

[Home](https://palatialpools.com.au/)/[Custom pool plumbing](https://palatialpools.com.au/pool-plumbing-melbourne/)/Custom manifolds and plant roomsManifolds and plant rooms

# Custom Pool Manifolds & Plant Room Design

A plant room should read like a diagram. Every suction and return line comes in on its own valve, every valve is labelled, and any pump, filter or sanitiser can be isolated without draining the system or shutting the pool down.

Request a quote[03 4517 6657](tel:+61345176657)

Individually plumbed

Each skimmer, main drain, return and feature line gets its own valve at the manifold.

Serviceable by design

Unions and isolation on every major component, with room to get the lid off.

Labelled and documented

Valves tagged and flow paths drawn, so the next person can read it.

Custom manifolds that let every line be set, isolated and serviced on its own.

## What makes a manifold good

01

### Flow paths you can see

The layout follows the water: suction lines into a common header, through the pumps, filters, heating and sanitation, then out to a return header. Anyone standing in front of it should be able to trace a drop of water through the plant.

02

### Isolation without drama

Unions either side of each pump, filter and heater, with valves that actually seal, mean a component can come out for service while the rest of the system stays primed and ready.

03

### Velocity kept in check

Headers and branch lines are sized so the water isn't forced through a bottleneck. Lower velocity means less friction, less noise and less wear on pumps and valves.

04

### Room for tomorrow

Capped tees and valve positions left for a future heater, spa circuit, water feature or valve actuator cost very little now and save a re-plumb later.

## From pad to plant room

Most pool equipment in Melbourne sits on a pad beside a fence, plumbed one piece at a time as things were replaced. That works until the pool has more than one job to do. Add a spa, a waterfall, heating and a second sanitiser, and a pad full of tees and short-cuts turns into a system nobody can read.

A designed manifold replaces those short-cuts with headers: one collecting every suction line, one distributing every return. Between them sit the pumps, filters, heaters and sanitisers, each on its own isolation valves. The result is easier to service, easier to diagnose and much easier to change later.

## Designed around the people who service it

We lay plant rooms out for the person standing in front of them: valves at a reachable height, gauges where they can be read, enough clearance to lift a filter lid or pull a cartridge, and a drain point that doesn't flood the floor. Every valve gets a tag, and you get a drawing of the flow paths.

## Process

On complex builds, the space is captured with LiDAR at 40 million points per square metre to 0.5 mm accuracy, reconstructed in COLMAP and TwinVision, and every pipe run and hydraulic calculation is modelled in OpenFOAM on Palatial's own frontier hardware, before a single fitting is cut.

Individually plumbed suction and return lines with 3-way diverter valves feeding a fibreglass filter and a variable-speed pump.

What we measure and specify

- Every suction, return and feature line traced and named
- Static head and pipe lengths for each circuit
- Pump duty points against the real system curve
- Clearances for service: lids, cartridges, unions
- Ventilation, drainage and heater flue requirements
- Future circuits and valve actuators planned in

What you get

### A plant you can read

Labelled valves and a flow-path drawing you can keep with the pool.

### Faster service, for life

Any component isolated and removed without draining or re-priming the whole system.

### A pressure-tested handover

Valves cycled, paths balanced and joints tested under load before sign-off.

Questions

## Custom Pool Manifolds & Plant Room Design: common questions

Is a custom manifold only for big pools?+

No. Any pool with more than one circuit benefits: a spa, a water feature, heating, or separate skimmer and main-drain lines. The manifold is sized to the pool, not the other way around.

Can you rebuild an existing messy equipment pad?+

Yes. We trace every existing line first, pressure test the buried pipework we plan to keep, then rebuild the above-ground plumbing as a proper manifold.

Do you supply a drawing?+

Yes. Every manifold we build is labelled, and you get a drawing of the flow paths and valve positions to keep with the pool's records.

How is a plant room job priced?+

Plant room and manifold work is quoted after we've inspected the site, traced the lines and agreed the scope. There's no one-size price for one-of-one work.

Related specialist plumbing

[Cross-coupled, multi-pump and dual-sanitiser set-upsPumps, filters and sanitisers that can back each other up with a turn of a valve.](https://palatialpools.com.au/multi-pump-dual-sanitiser-pool-plumbing-melbourne/)[Hydraulic design, flow and head-loss planningFlow, head and balance worked out before a single fitting is cut.](https://palatialpools.com.au/pool-hydraulic-design-melbourne/)[The one-of-one planning processCapture, model, build, prove. Every bespoke job follows the same path.](https://palatialpools.com.au/bespoke-pool-plumbing-design-process-melbourne/)[All custom pool plumbingRepairs through to full plant room builds.](https://palatialpools.com.au/pool-plumbing-melbourne/)

Try the [pump optimiser](https://palatialpools.com.au/pump-optimiser/) or the [filter sizing calculator](https://palatialpools.com.au/filter-sizing/) for a first look, or book a [pool inspection](https://palatialpools.com.au/inspections/).

Enquiries and quotes

## Talk to us about your plumbing

Send a few wide photos of the plant and a short description of what the pool needs to do. We'll come back with the right first step.

[03 4517 6657](tel:+61345176657)[0420 117 665](tel:+61420117665)[service@palatialpools.com.au](mailto:service@palatialpools.com.au)

Monday-Friday 9:30am-4:30pm, Saturday 9:30am-3:30pm. Sunday closed.

NamePhoneEmailSuburb (optional)How can we help?WebsiteA phone number or an email address is enough.

Send enquiry
