# Triple-Pump, Dual-Chlorinator Cross-Coupled Plant Room | Pool Hydraulics Case Study | Palatial Pools

URL: https://palatialpools.com.au/cross-coupled-pool-manifold-plant-room/

Case study: custom pool plumbing and hydraulic design for a 30 m lap pool and 10 m waterfall at a high-end private residence in Toorak. LiDAR-captured, modelled in OpenFOAM, 50 m static head.

[Home](https://palatialpools.com.au/)/[Custom pool plumbing and hydraulics](https://palatialpools.com.au/pool-plumbing-melbourne/)/Case studyCase study · Advanced pool hydraulics

# Triple-Pump, Dual-Chlorinator Cross-Coupled Plant Room

At a large private residence in Toorak, one plant room runs a 30 m lap pool and a 10 m waterfall that falls into an infinity-edge trough and collection system, from a room sitting well below the pool. We redesigned the hydraulics and rebuilt the room around a single cross-coupled manifold.

About 10 suction and return points are each plumbed in individually, so every circuit can be balanced, isolated and serviced on its own. 3-way diverter valves at every major junction let any pump drive either filter and either chlorinator, a non-return valve on every line holds back a 50 m static head, and the whole system was pressure-tested and hardened before sign-off.

The finished plant room: the cross-coupled manifold, 3-way diverter valves, twin fibreglass filters, pumps and chlorinators.

30 mlap pool

10 mwaterfall into an infinity-edge trough

~10individually plumbed suction and return points

50 mstatic head

Pool plant room design

## Scanned, modelled, then built

The plant room was captured with LiDAR at 40 million points per square metre to 0.5 mm accuracy, reconstructed in COLMAP and TwinVision, and every pipe run and hydraulic calculation was modelled in OpenFOAM on Palatial's own frontier hardware, before a single fitting was cut.

Modelling the hydraulics first meant pipe sizes, routes and valve positions were settled against the real room and the real head before installation started, and the scan stays on file as an as-built record for future servicing.

Twin fibreglass filters joined by the cross-coupled manifold, with the controllers on the backing board above.Each line comes into the manifold on its own, with a 3-way diverter at every major junction.

## Pool hydraulics at estate scale

A 30 m lap pool and a 10 m waterfall have very different flow demands, and the waterfall's infinity-edge trough and collection system has to stay in balance with the main pool.

Rather than teeing several circuits into a shared header, each of the roughly 10 suction and return points runs on its own line into the manifold. Flow can be set circuit by circuit, any one line can be isolated without disturbing the rest, and a fault traces back to a single pipe.

## A fully cross-coupled manifold

The core of the plant room is a fully cross-coupled manifold, built in-house from white PVC, with a 3-way diverter valve at every major junction. Any pump can drive either filter and either chlorinator.

Any pump can also feed the waterfall, feed the floor jets, draw from the trough, draw from the pool, or return to any of them, in combination or in sequence. Multi-mode selection valves change the setup with a turn of a handle instead of cutting and re-plumbing pipe.

## How the pumps run

The Neptune 2 HP DC variable-speed pump drives the main 28-inch filter. It can draw from the trough or the pool, but primarily draws from the pool's main drain and returns through the waterfall feeds and the pool returns.

In standard operation the Astral BX 2.0 HP runs as a high-flow circulation pump, pushing water fast to floor jets set about 15 mm off the pool floor. Along the 30 m lap pool, the jets sweep debris toward the infinity-edge end, where it flows over into the trough.

The Neptune 1.5 HP DC variable-speed pump completes the cross-coupled set of three.

## Waterfall and infinity-edge plumbing

The 10 m waterfall falls into an infinity-edge trough and collection system. Water collected in the trough runs through a dedicated 25-inch fibreglass filter with a leaf canister.

That trough loop also carries chlorinated water and sends it straight back up to the top, to the waterfall and the pool, so the collection side never sits as a dead end.

## Two chlorinators, one system

The plant room runs two chlorinators. The Lincoln chlorinator already on site was in good working order, so it was retained and reused: we don't throw out sound equipment. Alongside it is a PoolPro ultra low salt chlorinator (1500 ppm) with an accompanying magnesium mineral doser.

Both chlorinators can serve the pool and the trough and waterfall water, together or separately depending on load.

## Non-return valves and fault tolerance

The pool sits well above the plant room, so every pump works against a 50 m static head. Every line carries a non-return (check) valve, so whichever system fails or interacts with another, there is no direct overflow risk and no siphon effect. Siphoning is a common failure in infinity pools without properly designed plumbing.

The system is designed to keep running with more than one component out of service at the same time. Any pump, filter or chlorinator can be isolated for maintenance while the rest keep the pool and waterfall running, and the controllers have manual override so circulation and water quality hold while part of the automation is serviced.

What went in

## Equipment fitted

- Custom fully cross-coupled PVC manifold taking about 10 individually plumbed suction and return lines, with 3-way diverter valves at every major junction and a non-return (check) valve on every line
- Neptune DC 2 HP variable-speed pump, driving the main 28-inch filter
- Neptune DC 1.5 HP variable-speed pump
- Astral BX 2.0 HP pump, running high-flow circulation to the floor jets
- 28-inch fibreglass filter for the main pool, plus a 25-inch fibreglass filter with a leaf canister on the trough loop
- PoolPro ultra low salt chlorinator (1500 ppm) with a magnesium mineral doser
- Lincoln chlorinator, retained from the existing plant room and reused
- Pump and chlorinator controllers on a custom backing board, with manual override across all circulation and sanitation circuits

Related services: [pool pump installation](https://palatialpools.com.au/pool-pump-installation-melbourne/), [pool equipment installation](https://palatialpools.com.au/pool-equipment-installation-melbourne/) and [pool equipment repairs](https://palatialpools.com.au/pool-equipment-repairs-melbourne/).

Before sign-off

## Pressure testing and hardening

After installation the system went through an operational hardening period. It was run under high-pressure loads to simulate peak summer use and to stress-test the new PVC joints and valve seals.

The selection valves were cycled repeatedly, and the twin filter and chlorinator paths were checked for balanced flow and equal pressure. Small commissioning issues, such as slight pressure imbalances, were tuned out, and the system passed all pressure and flow tests.

Complex and fully customised

## The specialist plumbing behind this build

[Custom manifolds and plant roomsCustom manifolds that let every line be set, isolated and serviced on its own.](https://palatialpools.com.au/custom-pool-manifold-plant-room-design-melbourne/)[Cross-coupled, multi-pump and dual-sanitiser set-upsPumps, filters and sanitisers that can back each other up with a turn of a valve.](https://palatialpools.com.au/multi-pump-dual-sanitiser-pool-plumbing-melbourne/)[Hydraulic design, flow and head-loss planningFlow, head and balance worked out before a single fitting is cut.](https://palatialpools.com.au/pool-hydraulic-design-melbourne/)[Plant-room relocation and full re-plumbingNew runs sized for the new distance, with buried pipework tested before it's reused.](https://palatialpools.com.au/pool-plant-room-relocation-melbourne/)[Leak and pressure diagnosticsEach line isolated and tested on its own, so any digging starts in the right place.](https://palatialpools.com.au/pool-plumbing-pressure-testing-melbourne/)[Heat pump, gas and solar integrationCorrect order, bypasses and flow so each heat source does its job.](https://palatialpools.com.au/pool-heating-plumbing-integration-melbourne/)[Automation-ready plumbingActuator-ready valves, sensor points and clean cable routes.](https://palatialpools.com.au/automation-ready-pool-plumbing-melbourne/)[The one-of-one planning processCapture, model, build, prove. Every bespoke job follows the same path.](https://palatialpools.com.au/bespoke-pool-plumbing-design-process-melbourne/)

Enquiries and quotes

## Planning something similar?

Send photos of the current plant and a short brief of what the pool needs to do.

[03 4517 6657](tel:+61345176657)[0420 117 665](tel:+61420117665)[service@palatialpools.com.au](mailto:service@palatialpools.com.au)

Monday-Friday 9:30am-4:30pm, Saturday 9:30am-3:30pm. Sunday closed.

NamePhoneEmailSuburb (optional)How can we help?WebsiteA phone number or an email address is enough.

Send enquiry

## Planning a pool plant room or complex hydraulics?

Palatial Pools designs and builds custom plant rooms for pools with real hydraulic demands: long lap pools, waterfalls and infinity edges, many suction and return circuits, and high static heads.

[Custom pool plumbing and hydraulics in Melbourne](https://palatialpools.com.au/pool-plumbing-melbourne/)[Contact Palatial Pools](https://palatialpools.com.au/contact/)[03 4517 6657](tel:+61345176657)[03 4517 6657](tel:+61345176657)[service@palatialpools.com.au](mailto:service@palatialpools.com.au)
