# Bespoke Pool Plumbing Design Process Melbourne | Palatial Pools

URL: https://palatialpools.com.au/bespoke-pool-plumbing-design-process-melbourne/

How Palatial Pools plans one-of-one pool plumbing in Melbourne: capture the site, model the hydraulics, build in-house, pressure-test and hand over. Call 03 4517 6657.

[Home](https://palatialpools.com.au/)/[Custom pool plumbing](https://palatialpools.com.au/pool-plumbing-melbourne/)/The one-of-one planning processHow a one-of-one plant gets built

# The One-of-One Pool Plumbing Design Process

No two complex pools are the same, so no two plant rooms should be either. Every bespoke job follows the same disciplined path: capture the space, model the water, build it once, then prove it under load.

Request a quote[03 4517 6657](tel:+61345176657)

Captured

The space recorded accurately before any design.

Modelled

Every run and calculation worked out before a fitting is cut.

Proven

Pressure-tested, balanced and documented at handover.

Capture, model, build, prove. Every bespoke job follows the same path.

## Four stages, every time

01

### Capture the space

The plant room or pad is captured with LiDAR at 40 million points per square metre to 0.5 mm accuracy, then reconstructed in COLMAP and TwinVision, so the design starts from the real space, not a sketch.

02

### Model the hydraulics

Every pipe run and hydraulic calculation is modelled in OpenFOAM on Palatial's own frontier hardware, before a single fitting is cut: flows, heads, losses and balance for every mode.

03

### Build the plant room

Manifold, pumps, filtration and sanitation are built in-house, with every valve labelled and reachable for service.

04

### Pressure-test and harden

The system runs under high-pressure load, valves are cycled, paths balanced, and commissioning issues tuned out before sign-off.

## What we need from you

Tell us what the pool has to do: pool only, or spa, features, heating, cleaning and automation too. Tell us what bothers you about the current set-up: noise, cost, unreliability, access. Plans, photos and any service history help. Builders, landscapers and architects are welcome in the conversation early.

## What you get at the end

A plant that does every job it was designed for, a labelled manifold, a drawing of the flow paths and valve positions for each mode, and a commissioning record showing what was tested and how it performed.

## A worked example

Our triple-pump, dual-chlorinator cross-coupled plant room went through exactly this process. The case study walks through it step by step.

[See the cross-coupled plant room](https://palatialpools.com.au/cross-coupled-pool-manifold-plant-room/)

Individually plumbed suction and return lines with 3-way diverter valves feeding a fibreglass filter and a variable-speed pump.

What we measure and specify

- Brief: every job the pool must do
- Site capture and existing-line survey
- Hydraulic model for every mode
- Agreed drawings and scope before build
- In-house build with labelled valves
- Pressure test, balance and documented handover

What you get

### One design, built once

Problems solved on screen, not with a hacksaw on site.

### Documented

Drawings, mode chart and commissioning record.

### Proven under load

Tested and balanced before you take it over.

Questions

## The One-of-One Pool Plumbing Design Process: common questions

How long does the design stage take?+

It depends on the size and complexity of the job. We'll give you a timeline once we understand the brief and have seen the site.

Can you work with my builder or landscaper?+

Yes, and earlier is better. Sleeves, penetrations, drainage and plant-room size are all easier to get right before slabs and walls go in.

Is this only for new pools?+

No. Many bespoke jobs rebuild the plant for an existing pool that has outgrown its original set-up.

How is it priced?+

Bespoke plumbing is quoted after the site visit and brief, once the scope is clear. An inspection is often the right first step.

Related specialist plumbing

[Custom manifolds and plant roomsCustom manifolds that let every line be set, isolated and serviced on its own.](https://palatialpools.com.au/custom-pool-manifold-plant-room-design-melbourne/)[Hydraulic design, flow and head-loss planningFlow, head and balance worked out before a single fitting is cut.](https://palatialpools.com.au/pool-hydraulic-design-melbourne/)[Cross-coupled, multi-pump and dual-sanitiser set-upsPumps, filters and sanitisers that can back each other up with a turn of a valve.](https://palatialpools.com.au/multi-pump-dual-sanitiser-pool-plumbing-melbourne/)[All custom pool plumbingRepairs through to full plant room builds.](https://palatialpools.com.au/pool-plumbing-melbourne/)

Try the [pump optimiser](https://palatialpools.com.au/pump-optimiser/) or the [filter sizing calculator](https://palatialpools.com.au/filter-sizing/) for a first look, or book a [pool inspection](https://palatialpools.com.au/inspections/).

Enquiries and quotes

## Talk to us about your plumbing

Send a few wide photos of the plant and a short description of what the pool needs to do. We'll come back with the right first step.

[03 4517 6657](tel:+61345176657)[0420 117 665](tel:+61420117665)[service@palatialpools.com.au](mailto:service@palatialpools.com.au)

Monday-Friday 9:30am-4:30pm, Saturday 9:30am-3:30pm. Sunday closed.

NamePhoneEmailSuburb (optional)How can we help?WebsiteA phone number or an email address is enough.

Send enquiry
